Homage Forum

tafari wrote: ↑April 22nd, 2020, 12:53 pm

Yoda wrote:

tafari wrote: ↑April 22nd, 2020, 11:37 am
no sorcery, it is an easy job.

I take some Adrian hands or simular ones, suck them into acceton that the lume comes off.
I drilled a hole inside a wood plate, that the tube fit inside and the hand lying flat on the wood, tight inside. than I use only the dremel with a soft polishing bit and a little polish paste. I let it run slow and polishing the hands till they start to shine. afterwards I clean them and start polishing by hands with capecod. cleaning again and done, sounds ruff to use the dremel but it works very well. for the CP dummy I took a little
ss screw,1.2mm sand it to 1.1 mm and polished the thread side very well, cut it to length and press inside the minute hand. the last step using swiss C3 luminovo and lume each hand. after drying, I clean everything once with woman make up cotton. now they are finish for use.

Never seen anything that shiny before!

you had never seen the case


Gesendet von iPad mit Tapatalk

Tanukjaju wrote:

tafari wrote: ↑April 22nd, 2020, 12:53 pm

Yoda wrote:
Never seen anything that shiny before!

you had never seen the case


Gesendet von iPad mit Tapatalk

Nor his car.

Emilio wrote:Stealthy submariner. All in grey.

Sterile.

Ceramic matte insert.

Grey lume.

No shine reflection.


Now I need to do the hands and case.

tafari wrote: ↑April 22nd, 2020, 1:14 pm

Emilio wrote:Stealthy submariner. All in grey.

Sterile.

Ceramic matte insert.

Grey lume.

No shine reflection.


Now I need to do the hands and case.

I like this ceramic matte inserts, looks promising

Emilio wrote:

tafari wrote: ↑April 22nd, 2020, 1:14 pm

Emilio wrote:Stealthy submariner. All in grey.

Sterile.

Ceramic matte insert.

Grey lume.

No shine reflection.


Now I need to do the hands and case.

I like this ceramic matte inserts, looks promising

Apparently I'm not the first to think this a good design:

tafari wrote:

Emilio wrote:

tafari wrote: ↑April 22nd, 2020, 1:14 pm
I like this ceramic matte inserts, looks promising

Apparently I'm not the first to think this a good design:

it is very good, the grey lume is glowing in dark?

Yoda wrote: ↑April 22nd, 2020, 12:13 pm

tafari wrote: ↑April 22nd, 2020, 11:37 am

aris.dayton wrote:What sorcery is this?

this deserves its own thread, show us the way, master!

no sorcery, it is an easy job.

I take some Adrian hands or simular ones, suck them into acceton that the lume comes off.
I drilled a hole inside a wood plate, that the tube fit inside and the hand lying flat on the wood, tight inside. than I use only the dremel with a soft polishing bit and a little polish paste. I let it run slow and polishing the hands till they start to shine. afterwards I clean them and start polishing by hands with capecod. cleaning again and done, sounds ruff to use the dremel but it works very well. for the CP dummy I took a little
ss screw,1.2mm sand it to 1.1 mm and polished the thread side very well, cut it to length and press inside the minute hand. the last step using swiss C3 luminovo and lume each hand. after drying, I clean everything once with woman make up cotton. now they are finish for use.

Never seen anything that shiny before!

aris.dayton wrote:i thought it was gold

Yoda wrote: ↑April 22nd, 2020, 12:13 pm

tafari wrote: ↑April 22nd, 2020, 11:37 am
no sorcery, it is an easy job.

I take some Adrian hands or simular ones, suck them into acceton that the lume comes off.
I drilled a hole inside a wood plate, that the tube fit inside and the hand lying flat on the wood, tight inside. than I use only the dremel with a soft polishing bit and a little polish paste. I let it run slow and polishing the hands till they start to shine. afterwards I clean them and start polishing by hands with capecod. cleaning again and done, sounds ruff to use the dremel but it works very well. for the CP dummy I took a little
ss screw,1.2mm sand it to 1.1 mm and polished the thread side very well, cut it to length and press inside the minute hand. the last step using swiss C3 luminovo and lume each hand. after drying, I clean everything once with woman make up cotton. now they are finish for use.

Never seen anything that shiny before!