Page 521 of 526

Re: What are you working on now?

Posted: May 6th, 2025, 9:39 am
by wwwEvgeny
3 times the lever of the winding stem gone off after installing dial ImageImage not sure what it cause... tomorrow need disassemble again Image ImageImage happily the hands sitting tight Image

Sent from my SM-S9380 using Tapatalk


Re: What are you working on now?

Posted: May 6th, 2025, 2:37 pm
by buddhabar
@dj57

:thumbup:
Great job...congratulations. It's always a pleasure to wear an Omega on your wrist.
Was the case already designed to accommodate a 41mm dial?

What are you working on now?

Posted: May 6th, 2025, 2:44 pm
by dj57
buddhabar wrote::thumbup:
Great job...congratulations. It's always a pleasure to wear an Omega on your wrist.
Was the case already designed to accommodate a 41mm dial?
Thanks Image
The 46mm case, yes. It’s for a ~41mm dial (already found a new home)
The 44mm case, it’s for a 38.5-39mm

Re: What are you working on now?

Posted: May 6th, 2025, 5:04 pm
by buddhabar
dj57 wrote: May 6th, 2025, 2:44 pm
buddhabar wrote::thumbup:
Great job...congratulations. It's always a pleasure to wear an Omega on your wrist.
Was the case already designed to accommodate a 41mm dial?
Thanks Image
The 46mm case, yes. It’s for a ~41mm dial (already found a new home)
The 44mm case, it’s for a 38.5-39mm
:thumbup: perfect

Re: What are you working on now?

Posted: May 7th, 2025, 12:38 am
by NortON
wwwEvgeny wrote: May 6th, 2025, 9:39 am 3 times the lever of the winding stem gone off after installing dial ImageImage not sure what it cause... tomorrow need disassemble again Image ImageImage happily the hands sitting tight Image

Sent from my SM-S9380 using Tapatalk
Great work E! :clap:

Re: What are you working on now?

Posted: May 7th, 2025, 2:17 am
by McBuell
dj57 wrote: May 6th, 2025, 8:57 am OMEGA mariage watches

1.) 46mm case
Here the dial had to be recused very little
Image
Image

2.) 44mm case
Here the dial had to be reduced ~2mm
Image
Image
Image
Image
Image
Image
Image
that 46 case is beautiful...is it AliE's? :)

Re: What are you working on now?

Posted: May 7th, 2025, 2:50 am
by dj57
McBuell wrote:
dj57 wrote: May 6th, 2025, 8:57 am OMEGA mariage watches

1.) 46mm case
Here the dial had to be recused very little
Image
Image

2.) 44mm case
Here the dial had to be reduced ~2mm
Image
Image
Image
Image
Image
Image
Image
that 46 case is beautiful...is it AliE's? :)
Yes, it’s from AliE
https://a.aliexpress.com/_EuOIqj0
If you search, you may find the same case much cheaper.

Re: What are you working on now?

Posted: May 7th, 2025, 6:41 am
by wwwEvgeny
NortON wrote: May 7th, 2025, 12:38 am
wwwEvgeny wrote: May 6th, 2025, 9:39 am 3 times the lever of the winding stem gone off after installing dial ImageImage not sure what it cause... tomorrow need disassemble again Image ImageImage happily the hands sitting tight Image

Sent from my SM-S9380 using Tapatalk
Great work E! :clap:
Thank you! crown is left, but can ware it without brevet )))) for some time
.
The balance is the beast, can hear it ticking from one meter )))
.

Re: What are you working on now?

Posted: May 7th, 2025, 10:44 am
by McBuell
dj57 wrote: May 7th, 2025, 2:50 am
McBuell wrote:
dj57 wrote: May 6th, 2025, 8:57 am
that 46 case is beautiful...is it AliE's? :)
Yes, it’s from AliE
https://a.aliexpress.com/_EuOIqj0
If you search, you may find the same case much cheaper.If you search, you may find the same case much cheaper
Special thanks! :)

Re: What are you working on now?

Posted: May 7th, 2025, 12:24 pm
by NortON
wwwEvgeny wrote: May 7th, 2025, 6:41 am
NortON wrote: May 7th, 2025, 12:38 am
wwwEvgeny wrote: May 6th, 2025, 9:39 am 3 times the lever of the winding stem gone off after installing dial ImageImage not sure what it cause... tomorrow need disassemble again Image ImageImage happily the hands sitting tight Image

Sent from my SM-S9380 using Tapatalk
Great work E! :clap:
Thank you! crown is left, but can ware it without brevet )))) for some time
.
The balance is the beast, can hear it ticking from one meter )))
.
Awesome result! :clap: :clap: :clap: