What are you working on now?
- Mellons
- Chief bottle washer
- Posts: 4833
- Joined: April 11th, 2018, 6:59 am
-
MM perv
Microbrand guru
5 year veteran
Frequent Flyer
Moderator
VIP
Prolific poster
HF veteran
Italiano addict
Skillful builder
Good neighbour
Re: What are you working on now?
That bracelet only works with that watch head!
“The problem with the world is that the intelligent people are full of doubts, while the stupid ones are full of confidence”
http://www.homage-forum.com/viewtopic.php?t=27
http://www.homage-forum.com/viewtopic.php?t=27
- civic4982
- VIP
- Posts: 1417
- Joined: April 11th, 2018, 7:46 pm
-
5 year veteran
Frequent Flyer
VIP
Prolific poster
HF veteran
Italiano addict
Re: What are you working on now?


Sent from my iPhone using Tapatalk
- toofsy
- Watch Addict
- Posts: 762
- Joined: July 20th, 2018, 11:01 am
-
5 year veteran
Frequent Flyer
HF veteran
Strap maker
Skillful builder
Re: What are you working on now?
Old jackson Dumbo midcase reshapping
last stage with 1200 grit sandpaper
last stage with 1200 grit sandpaper
You do not have the required permissions to view the files attached to this post.
IconRays - aNYstrap - Ateliers d'Embellie
- Yoda
- Honorary moderator
- Posts: 8080
- Joined: April 11th, 2018, 9:16 am
- Location: Stockholm
-
Mini Chat Squatter
Car lover
Bike lover
Knife maker
Animal
5 year veteran
Frequent Flyer
VIP
Prolific poster
HF veteran
Watchmaker
Good neighbour
- toofsy
- Watch Addict
- Posts: 762
- Joined: July 20th, 2018, 11:01 am
-
5 year veteran
Frequent Flyer
HF veteran
Strap maker
Skillful builder
Re: What are you working on now?
Thanks boss...
Impossible to press the bezel with the original gasket...maybe too much sanded down on the top area...however it works without the gasket...do I have to add GS hypo cement?
I have to order T25 plexi, reshape the CG, solder the brass NW tube, order a solid CB...
You do not have the required permissions to view the files attached to this post.
IconRays - aNYstrap - Ateliers d'Embellie
- Emilio
- Doom Slayer
- Posts: 8556
- Joined: April 11th, 2018, 3:29 am
- Location: Spain
- Contact:
-
Mini Chat Squatter
I'm hot
Animal
5 year veteran
Frequent Flyer
Moderator
VIP
Prolific poster
HF veteran
Italiano addict
Good neighbour
Re: What are you working on now?
Yes, a bit of sealant would be a good idea.toofsy wrote:Thanks boss...
Impossible to press the bezel with the original gasket...maybe too much sanded down on the top area...however it works without the gasket...do I have to add GS hypo cement?
I have to order T25 plexi, reshape the CG, solder the brass NW tube, order a solid CB...
Maybe teflon tape could work too? (Don't quote me on this)
Panerai reference pictures
https://mega.co.nz/#F!8R0FWaoS!IAasZXfb14Z7R1H6CLYp6w
Instagram
http://instagram.com/emisansev
IMGUR Albums
http://homage-forum.com/viewtopic.php?f=8&t=3508
https://mega.co.nz/#F!8R0FWaoS!IAasZXfb14Z7R1H6CLYp6w
http://instagram.com/emisansev
IMGUR Albums
http://homage-forum.com/viewtopic.php?f=8&t=3508
- hako
- Moderator
- Posts: 2504
- Joined: April 11th, 2018, 3:46 pm
- Location: Germany
-
5 year veteran
Frequent Flyer
Moderator
VIP
Prolific poster
HF veteran
Seiko specialist
Mad scientist
Good neighbour
Re: What are you working on now?

Asciiwhite would even be less niminy-piminy and recommend silicon to glue it on

====================================
Da builds: http://homage-forum.com/viewtopic.php?f=5&t=59#p101
====================================
Da builds: http://homage-forum.com/viewtopic.php?f=5&t=59#p101
====================================
- straps68
- Sponsor
- Posts: 2448
- Joined: April 11th, 2018, 2:13 pm
- Location: Sandara Leatherworks
-
5 year veteran
Frequent Flyer
Moderator
VIP
Sponsor
Prolific poster
HF veteran
Strap maker
Re: What are you working on now?


straps68
My buckles My straps
Flickr: https://www.flickr.com/photos/sandara_l ... rks/albums
Builds: 6152/1 mini 2 mini 1 Ti

My buckles My straps
Flickr: https://www.flickr.com/photos/sandara_l ... rks/albums
Builds: 6152/1 mini 2 mini 1 Ti

- Yoda
- Honorary moderator
- Posts: 8080
- Joined: April 11th, 2018, 9:16 am
- Location: Stockholm
-
Mini Chat Squatter
Car lover
Bike lover
Knife maker
Animal
5 year veteran
Frequent Flyer
VIP
Prolific poster
HF veteran
Watchmaker
Good neighbour
Re: What are you working on now?
It will be an extensive conversion, it's a nice orphan KW non incabloc alarm movement and I plan to make it a SW incabloc non alarm movement. Thanks to Erlendh for this $100 movement!tafari wrote: ↑July 24th, 2019, 1:47 pmall the to are nice ones, waiting for the 3. with gen parts to see I guess it will be a beauty tooYoda wrote:The one in the middle is a work for a member here and I hope that the one to the right will be sold to the interested party I discussed the details with.
The last one is a project, but it will be a full blown SW incabloc rebuilt with gen parts soon.
I made the intermediate bridge for the stem and setting parts recently, having it plated next week.
I believe that I bought some of the last gen parts available for the SF240 a few years back. Now that I also have found the high cannon pinion/hour wheel set I can build a helicopter! LOL!
Enviado desde mi fucking Samsung S8.
-
- VIP
- Posts: 351
- Joined: April 12th, 2018, 12:07 pm
-
5 year veteran
Frequent Flyer
VIP
HF veteran
Italiano addict
Re: What are you working on now?
It was my pleasure, glad I finally was able to help you with something, after so many years with things the other way around.Yoda wrote:It will be an extensive conversion, it's a nice orphan KW non incabloc alarm movement and I plan to make it a SW incabloc non alarm movement. Thanks to Erlendh for this $100 movement!
I made the intermediate bridge for the stem and setting parts recently, having it plated next week.